Showing posts with label classic car restoration. Show all posts
Showing posts with label classic car restoration. Show all posts

Sunday, 27 March 2016

Fairway taxi.Welding inner wheel arches and floor.

My taxi had badly rusted inner wheel arches. Really only visible with the rear wheels off and the interior trim and seats removed from the back. I've already welded up much of the bodywork,links to more photographs etc are on this page.

 
 This was the hole in the drivers side inner wheel arch,the area just in front of the wheel where the seat bottom rests was also rotten. These holes were made just by pressing the rust bubbles with a finger.


Using a thin cutting disc in an angle grinder the rot was cut out and cuts made to get back to sound metal.Using a depressed centre disc in the angle grinder the hole edges were cleaned up. A piece of card was pressed down onto the hole to make a pattern for a plate,cut approx 1/4 inch larger all round to sit under the hole.


The metal plate was curved and some cuts made to get the sharper bends,these cuts were then welded back together when the shape was finalised when the repair plate fitted accurately in place.The raised section or flange replaces the original which had started to rust badly and enabled the plate to fit accurately and strengthen the section it is welded to. 


The plate was welded in place and the welds partially ground down.The area is concealed so it seemed pointless to spend time making an invisible repair. Some seam sealer was used to stop any water access between the new section and the original panels.The plate is thicker than the original metal it replaces would have been and the arches are now considerably stronger than they were and probably stronger than when new.Supposedly the MOT (test for fitness) on these vehicles is very strict. I have seen enough of these vehicles (even ones in service) with extensive corrosion that I believe this is a myth.

Saturday, 14 February 2015

Under bonnet blanket on Rover P5b

The under bonnet blanket on my Rover was missing,these keep the heat from the engine from damaging the paint on the bonnet.
I made a blanket from fire resistant wadding between black cotton sheet. The cotton was treated with a mixture of Borax and Boracic acid to make it fireproof. The sheet was held in place with thin steel wire. It tucks under the bonnet supports.






Tuesday, 27 January 2015

Keeping the patina on an old classic car.

I've started a facebook group for the owners of classic cars who would rather use them than keep them locked away or take them to shows on a trailer. If you have a car you've restored on a budget,where you've adapted parts,sprayed and welded outside don't be shy,be proud of what you have achieved.


If you have a car that you've restored without spraying and chroming to within an inch of its life,join the Oily Rag restoration group. The link to it is here.

Monday, 15 September 2014

Cleaning fouled spark plugs.

Some people say there is nothing in a spark plug to wear out.That might be true but they do eventually get covered in a layer that can short them out so that they don't spark.This gives a misfire at best or stops the engine at worst.These plugs I removed from my V8 engined P5b Rover. The choke mechanism was faulty and the engine was running on a mixture that was too rich.


 Using a combination of a solvent and oven cleaner it is possible to make the plugs almost as good as new.This avoids using a grit blaster (which most of us don't  have) and avoids any grit or sand being left behind to damage the engine.


No wire brushing or need for machinery and fancy chemicals. Details are on a spark plug cleaning page.


Tuesday, 9 September 2014

Rubber door seals on the P5b.

I was getting fed up with the wind noise and rain coming in around the doors of the Rover P5b.
Door seals are available but very expensive for what are really just bits of rubber. I made some out of some sections I bought to repair the door seals on my transit.
These give a double seal around the door and fit inside the original door seal housing.


The new seals were glued together at the corners and the wind noise and the rain are now kept on the outside of the car.

Saturday, 21 June 2014

Taxi tantrums,the worlds most reliable car starts playing up.

I had a problem with the old taxi. The problem started as a minor one with the car being hard to start if parked facing uphill. gradually it got worse,I traced it to air getting in via the top of the priming pump on top of the filter.
I cut the top off and welded a plate over it (I think the diaphram was leaking).
. This got the thing running but air still got in and only by revving the engine hard every few minutes would it keep running it was also down on power.
Eventually I rigged up a temporary system using a squeeze type priming pump and a couple of inline filters. This seems to work well,so I've decided to leave it alone for the time being.




Sunday, 1 June 2014

Welding up the fairway doors part two.

The rot cut out left a bigger hole over half the door skin to bottom
is missing
After welding in some plates the seams were skimmed over with filler.

Wednesday, 28 May 2014

Car boot bargains,they just keep coming.

Went to a car boot this sunday. Julies car boot near Yarmouth. I did a stall to get rid of some stuff but came back with a load more.

I bought a compressor,a spray gun,tyre inflator and an air line. Also some old cast iron seat ends,an old but nice and solid petrol engine compression tester and some odd spanners. The spanners will go up for sale on the web site. I think now ebay seems to have shot itself in the foot again and choked off many small sellers that car boots are now going to be a better place to find the odd bargain. certainly for selling smaller items ebay is no longer as attractive for buyers or sellers as it once was.

Thursday, 15 May 2014

A bit of woodwork on the car .

One problem that the rover P5 and P5b have is water coming in at the ends of the windscreen and rotting out the metal behind and spoiling the trim especially the ends of the dashboard.
The wood fillets in the corners discolour and delaminate. I removed the wood from the drivers side nd the back of it was pretty badly damaged. the screws securing the panel are hard to locate but on this fillet they had started to give up the ghost anyway.

The area behind the panel was in reasonable order,some surface rust treated with fluid film. The panel was repaired and then fitted back in. Originally I had removed it to replace the furflex trim around the doors. This is secured with tacks to some strips recessed into the door openings.


Thursday, 8 May 2014

Sound proofing the Rover P5b.

I noticed when I took the radio out of the rover that some of the soundproofing felt had been removed from the dash panel area. I took the radio and the panel it fits into out and replaced the missing material.According to a couple of people I spoke to there should be more material behind the glove box and I have replaced this too.

Friday, 25 April 2014

MOT on the rover p5b. No tax and no tax disc.

I took the rover for its MOT today and it passed with no advisories. Due to its status as a historic vehicle (a reminder of when this country had a thriving car manufacturing industry) it qualifies for free road tax. Its tax disc is marked as no payment made. The EU in another interference in English affairs are proposing to do away with tax discs,our weak government will go along with this as they allow the Germans and others to do more damage to this country in peacetime than they ever did in war.
How long before these parasites want old cars off the road ?

Tuesday, 8 April 2014

Repairing and restoring.some old leather car seats

The seats in my rover p5b were pretty grim but I had a secondhand set also in very poor condition to practice on.
They had been painted and were very hard and cracked,the first thing to do was rub them carefully with thinners to get the paint off.

The seat back was bad,cracked and creased.
I experimented on another scrap seat and found most cracks were actually in the painted surface and they could be smoothed with fine wet and dry or a wire wool pad.
The front panel of the seat was heavily painted and stiff,most of the paint was removed with thinners.
After much cleaning with an alcohol based cleaner the dye was rubbed into the cracks and then a fine coat sprayed on,the improvement to the leathers texture was most noticeable.

The seat after a thin sprayed coat of dye.I found the dye too thick to spray with an air brush and used a spray gun (gravity feed type) and set on minimum it gave a very fine spray.The seat still has to have another coat (maybe) and then has to be sealed.

Thursday, 27 February 2014

Rover p5b featured on another site.

My Rover p5b is featured on this web site. The heading picture isn't very flattering but the article hopes to encourage anyone thinking of having a go at using a classic car to do so.
I hope it does.


Monday, 17 February 2014

Curing the thirst of the V8 in the Rover P5b

The tick over or idle of the Rover had been lumpy for some time and setting the carbs didn't seem to help. I went through the ignition replacing and repairing but no real difference.
The fuel consumption was pretty horrendous and the car would tick over albeit it a bit more lumpy even when cold without choke.
I pulled out the starter valves.these act as a choke on HIF6 carbs letting through a rich mixture. One was pretty worn but on one carb the O ring had broken up completely. I replaced both and although I still have to reset the carbs the V8 now idles slowly without trying to cut out or foul its plugs.

Thursday, 12 December 2013

Transit what to do with it?.

I really dont know what to do with my old transit motorhome. I hardly ever use the poor old thing,it just stands outside looking forlorn. I spent a lot of time welding it and rebuilding the engine but just dont get the time to use it.

I guess if I sell it I will regret it but in the meanwhile what use is an old motorhome other than for motorhoming?.

Wednesday, 18 July 2012

Rusty doors

Looks to me like there's the odd spot of rust in this door bottom off the transit.

Typically the rust you can see on this Mk1 transit door is just the tip of an iceberg,the hole will get much bigger with a bit of prodding and poking.The vehicle spent the past few years parked up on Lowestofts dockside where it was wetted by sea spray every time the wind blew.

Sunday, 25 March 2012

Car booty in a taxi.

I took a load of stuff to the local car boot,Julies Car boot at Burgh Castle.There didn't seem much to take at first so I just loaded it in the taxi but ended up pretty much filling the old girl.When it's all laid out it looks pretty nigh impossible to get it all back in it.
I didn't do too bad getting rid of some gear that there wouldn't really have been a place for at the new home.I don't like the Kessingland car boot,although its closer they tend to squeeze you up together and have all sorts of sily rules about where you can go and what times you're allowed to go on,I can do without a load of petty aggro first thing on a sunday morning.